|
Extra Large Canopy
with Screen Shade 20'x12'
90255/ 90256 |
|
|
| |
Part No. |
Description |
Qty. Req. |
| 1. |
 |
Peak Center Pole |
2 |
| 2. |
 |
Shock Corded Roof Pole |
4 |
| 3. |
 |
Shock Corded Center Roof Pole |
2 |
| 4. |
 |
Supporting Pole #7 |
4 |
| 5. |
 |
Supporting Pole #7B |
8 |
| 6. |
 |
Shock Corded Eave Pole 12' Side |
2 |
| 7. |
 |
Shock Corded Eave Pole 20' Side |
4 |
| 8. |
 |
Leg #6B |
12 |
| 9. |
 |
Leg #6 |
6 |
| 10. |
 |
Roof Center Hub |
1 |
| 11. |
 |
Roof End Hub |
2 |
| 12. |
 |
Eave Corner Connector |
4 |
| 13. |
 |
Eave Center Connector |
2 |
| 14. |
 |
Base Plate |
6 |
| 15. |
 |
Steel Stake 8" |
26 |
| 16. |
 |
Guy Lines |
4 |
| 17. |
 |
Fabric Skin |
1 |
| 18. |
 |
Carrying Bag |
1 |
| |
|
Step 1-
Lay out all the parts. Connect all the Shock Corded pole sections
together. Lay out all the shock corded eave poles as shown in Diagram 1.
Insert the eave poles into the cave corner connectors. |
|
|
|
Step 2-
Assemble the Peak Center pole (2B/1) with the Roof center hub and the
Roof end hub. Then attach the Shock Corded roof pole (2B/2) to the roof
end hub, as shown in Diagram 2. Connect poles, 7B-7-7B, hook the
Supporting pole by snapping the hook to the Roof center pole, and cave
pole, as shown in Diagram 2. |
|
Step 3-
Spread the screen house skin flat on the ground. Unzip all the doors for
easier setup. Drape the screen house skin over the roof poles of the
frame, pull the skin till taut from corner to corner. Buckle the straps
inside the screen house around each eave pole. |
 |
|
|
Step 4-
Connect the leg poles into the cave corner and center connectors to
raise the screen house, see Diagram 4. When installing legs please
install the 20 ft. side first by raising each of the 3 legs (6B) one at
a time. Make sure that leg #6 is the closest to the ground. Insert the
plastic base plate onto the leg ends as shown in Diagram 4. |
|
Step 5-
Secure the Screen house down by inserting the hooks, #C, located on the
outside lower corners of the screen house, to one of the three holes in
the leg pole. Secure the screen house to the frame by buckling the tabs,
#D, around the poles. Secure the screen house down to the ground by
inserting the stakes through the loops and D- rings. The stake loops are
located at #E, and the D- rings are located at # F. If you are setting
this screen house on a deck or concrete you may hook the D-rings to the
plastic base or attach a weight, or sand bag to the D-rings.
Step 6-
Tie the loose end of each guy line to the D- rings located on the top
corners of the screen house roof, #G. On the other end of the guy line
extend the loop and stake it 3ft from the corner base of the screen
house. Adjust the tension of the guy line with the slider. You may also
tie the guy lines to a tree or fence for extra support.
|
|
|